Avanti CF103 User Manual download pdf (Page 31)

User’s Manual 31

13. Ordering spare parts

Fig. 21

Rating plate on

the work cage back frame

Information signs

Operating instructions inside the lift

QUICK GUIDE – Work cage SHARK

s /NLYPERSONNELTRAINEDTOUSETHEWORKCAGEMAYOPERATETHISSYSTEM

s "EFOREUSINGTHEWORKCAGECAREFULLYREADANDOBSERVEALLOPERATINGINSTRUCTIONS

(For details, see User’s Manual and Installation Manual)

Pendant control Safety brake

Emergency

stop

Down

Brake leaver

To open the brake

1. Losen the Safety brake wire

by taking work cage up.

2. Press down Safety brake

leaver until brake

disengages.

Stop button

Inspection window

Flywheel must turn during work

cage operations.

Traction hoist

Brake leaver

insertion point

Insert brake

leaver into

insertion point and

pull upwards for

descent.

Hand wheel

For taking lift up

manually.

Down

1. Losen the Safety brake.

2. Insert brake leaver into

break leaver insertion point

and loosen motor brake by

slowly pulling upwards.

1. Mount hand wheel on top

of the traction hoist.

2. Losen motor brake

using the brake leaver

(see above) while turning

the hand wheel counter

clockwise.

Manual operation

45541105 – Quick guide EN / UL

QUICK GUIDE – Work cage SHARK

s /NLYPERSONNELTRAINEDTOUSETHEWORKCAGEMAYOPERATETHISSYSTEM

s "EFOREUSINGTHEWORKCAGECAREFULLYREADANDOBSERVEALLOPERATINGINSTRUCTIONS

(For details, see User’s Manual and Installation Manual)

Pendant control

Traction hoist

QUICK GUIDE – Work cage SHARK

s /NLYPERSONNELTRAINEDTOUSETHEWORKCAGEMAYOPERATETHISSYSTEM

s "EFOREUSINGTHEWORKCAGECAREFULLYREADANDOBSERVEALLOPERATINGINSTRUCTIONS

(For details, see User’s Manual and Installation Manual)

Safety wire

Drive wire

Emergency top limit STOP switch

Top limit STOP switch

Work cage SHARK Sliding door Work cage SHARK Double door

Wire guide

Guide wire

Bottom safety

stop bar

Bottom safety

stop switch

Emergency stop

13.5 Rating plate/information signs13.1 Wire/ropes

In addition to the item number and name of

the spare part, always state the traction hoist

type, wire diameter and production number!

13.2 Motor and brake

In addition to the item number and name of

the spare part, always state the motor type

and the type and coil voltage of the brake!

13.3 Electric control

When ordering spare parts or making requests,

always state the electricity category and wiring

chart number. See the rating plate at the con-

nection cabinet. There is a wiring chart in the

connection cabinet and in the motor terminal box.

13.4 Safety brake

In addition to the item number and name of the

spare part, always state the safety brake type,

the wire diameter and lift serial no.

A spare parts list is available from the

supplier or directly from AVANTI.

Verify the completeness and legibility of all

rating plates/information signs (see Fig. 21).

Replace missing or illegible plates/signs!

MATERIALE: 3M 7980 hvid polyesterfolie

sort -

SL 021gul

17, 36 punkt

FARVE SPECIFIKATION:

FONT SPECIFIKATION:

STR (CAD):

ABC 123

EKS:

CAUTION

Before using, check all parts for proper function and damage

to component parts. Do not use a damaged or improperly

functioning work cage.

A work cage exposed to excessive heat, as in the case of

fire, should be immediately removed from service and

destroyed due to loss of structural strength.

Do not permit oil, grease or slippery material to accumulate

on climbing or gripping surfaces.

The work cage is designed with rated work load of 533 lbs

(240 kg). The total combined load of each worker and all

materials should not exceed the rated working load. Do not

overload.

Do not allow unstable objects, such as barrels, boxes, tools

and debris to accumulate on the work surface.

Do not use a ladder or other device on a work cage to gain

greater heights.

Do not ride on top of the work cage. Tools, materials, and

equipment should not be stored on top of the work cage.

Do not apply impact loads to a work cage.

Do not use acids or other corrosive substances on or in a

work cage without consulting the work cage manufacturer for

specific instructions.

Scaffold and tools shall not be allowed to contact

unprotected, energized electrical lines or equipment. Maintain

a minimum safe distance of at least 10 ft. (3 m). Consult the

power company to shut off power or insulate/relocate the line

if working closer than 10 ft.

Before using, refer to manufacturer’s instructions.

Never attempt to straighten a deformed side rail or decking

member.

45541085

FORBEHOLDT SETIKET

CAD NAVN:

Helvetica Neue medium/ital.

FONTNAVN(E):

FARVE: SPEC:

Avanti Stigefabrik A/S

TLF.: 48249024

3400 Hillerød

Høgevej 19

C01-0423

Setiket label System C01 - UL instruction

31.07.07

C01-0423

45541085

KOPIERET ELLER OVERGIVET TIL TREDIE PART UDEN VORES SKRIFTLIGE TILLADELSE.

GODKENDT SETIKET:

!! MÅ KUN ÆNDRES I CAD-SYSTEM !!

DENNE TEGNING TILHØRER SETIKET A/S. DEN MÅ IKKE BLIVE BRUGT AF,

QF.2008-0

INIT:

ORIGINAL TEGNING

ÆNDRING:

DS/ISO 2768-m

ALLE MÅL I MM

HVOR INTET ANDET ANGIVET

REV.

SKALA: 1:1

GEN. TOLERANCE:

DATO: INIT: DATO:

TEGNET:

SIDE 1 ER FØLGEBREVSIDE 2 AF 2

Setiket A/S

E-mail: [email protected]

DK-6715 Esbjerg N

Tel. +45 76 14 76 00, Fax +45 76 14 76 01

REV.

SETIKET TEGNINGNR.

UNDERSKRIFT:

GODKENDTIKKE GODK.

TEKST / TITEL:

KUNDE:

(sæt X): (sæt X):

KUNDE GODKENDELSE:

KUNDE P/N:

SETIKET P/N:

DATO:

equipment should not be stored on top of the work cage.equipment should not be stored on top of the work cage.

Do not apply impact loads to a work cage.Do not apply impact loads to a work cage.

Do not use acids or other corrosive substances on or in aDo not use acids or other corrosive substances on or in a

work cage without consulting the work cage manufacturer forwork cage without consulting the work cage manufacturer for

specific instructions.specific instructions.

Scaffold and tools shall not be allowed to contactScaffold and tools shall not be allowed to contact

unprotected, energized electrical lines or equipment. Maintainunprotected, energized electrical lines or equipment. Maintain

a minimum safe distance of at least 10 ft. (3 m). Consult thea minimum safe distance of at least 10 ft. (3 m). Consult the

power company to shut off power or insulate/relocate the linepower company to shut off power or insulate/relocate the line

if working closer than 10 ft.if working closer than 10 ft.

Before using, refer to manufacturer’s instructions.Before using, refer to manufacturer’s instructions.

Never attempt to straighten a deformed side rail or deckingNever attempt to straighten a deformed side rail or decking

member.member.

4554108545541085

MAX

533 lbs

(240 kg)

Max. 1 person

Please Read and Understand

Cautions and Instructions of “User Manual”.

Please Observe the Following Safety Precautions.

WORK CAGE

AS TO LOAD CAPACITY ONLY

12XZ

CAUTION: Only personnel trained to use the work cage

may operate this system.

CAUTION: When using the system, bring communication

equipment.

CAUTION: Risk of injury. Acids and other corrosive

substances may severely affect the strength of

metal scaffolding devices. Use extreme care

around such materials and follow instructions.

CAUTION: Risk of electric shock.

Metal scaffolding devices should not be used

where contact may be made with electrical

circuits. Refer to instruction manual.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 63 64

Comments to this Manuals

No comments

Avanti CF103 User Manual Page 31

Comments to this Manuals

Related products and manuals for Unknown Avanti CF103